» Flange & Fitting » ASME B16.5 Reducing Flange

ASME B16.5 Reducing Flange

August 15, 2019

What’s A Reducing Flange?

ASME B16.5 has endorsed the design and construction of a reducing flange. The reducing flange is used to make a reduction in the diameter of the pipe. A reducing flanged joint consists of a reducing flange and a standard flange, functioning like a reducer fitting. As illustrated in Figure-1, the larger end of reducing flange A, which is in contact with the standard flange B, is known as “the size from which the reduction is being made”; the smaller end of the reducing flange A, which will be welded to a pipe, is known as “the size to which the reduction is being made”. The flow should travel from the smaller size to the larger. If the flow direction were reversed, severe turbulence could develop.

Reducing flange joint

Figure-1: a reducing flange joint: reducing WN flange A and standard WN flange B.

As depicted in Figure-1, the reducing flange is generally constructed in 3 sections: i – flange facing, ii – flange thickness, iii – flange hub. Its characteristics are obvious: the facing dimensions, thickness, bolting dimensions, and outside diameter of the reducing flange are the same as those of the standard flange of the size from which the reduction is being made. The hub dimensions as well as the bore diameter of the reducing flange are generally the same as those of the standard flange of the size to which the reduction is being made.

Why Using a Reducing Flange?

2 WN flanges + reducer

Figure-2: two standard welding neck flanges with one reducer to achieve the reduction in piping.

In order to make a reduction in the pipe line with two standard welding neck flanges, an additional reducer shall be used as illustrated in Figure-2. The overall length of this configuration is 2L+H, which is much longer than L+M of a reducing flanged joint as illustrated in Figure-1. It means that the use of reducing flanges can effectively save space in crowed situation. In fact, the reducing flange is most frequently used in installations with limited space.

Types of Reducing Flanges

Reducing threaded flange without hub

A typical reducing threaded flange without hub made from ASME B16.5 blind flanges.

Reducing flanges manufactured in accordance with ASME B16.5 are available in Class 150 through 2500. The facing of the reducing flange shall be the same as that of the mating standard flange. Generally, four types of reducing flanges are available according to the standard: reducing welding neck flanges, reducing slip on flanges, reducing threaded flanges, and reducing socket welding flanges. The reducing welding neck flange must be furnished with hub and the hub dimensions shall be the same as those of the standard flange of the size to which the reduction is being made. Reducing flanges of threaded, slip on or socket welding types may be furnished with or without hub. The hub dimensions shall be at least as large as those of standard flange of the size to which the reduction is being made. The hub may be larger or omitted as detailed in the table below.

*Size A*Size B
1"1/2"
1-1/4"1/2"
1-1/2"1/2"
2"1"
2-1/2"1-1-4"
3"1-1-4"
3-1/2“1-1/2"
4"1-1/2"
5"1-1/2"
6"2-1/2"
8"3"
10"3-1/2"
12"3-1/2"
14"3-1/2"
16"4"
18"4"
20"4"
24"4"
*Size A: nominal pipe size of the larger end of a reducing flange; *Size B: the smallest NPS for the smaller end of a reducing flange, which requires a hub.

If the “smaller-end” (reducing outlet) of the flange is smaller than those listed in Column “Size B”, the reducing flange may be furnished without hub (made from a blind flange). Class 150 reducing threaded flanges do not have a counterbore. Class 300 and higher pressure reducing threaded flanges will have depth of counterbore Q of 7 mm for NPS 2 and smaller tapping and 9.50 mm for NPS 21∕2 and larger. The diameter Q of counterbore is the same as that given in the tables of threaded flanges for the corresponding tapping.

Designation of Reducing Flanges

Reducing flanges shall be designated by the NPS for each opening. Two examples are provided below:

  •  8″ × 3″ SCH40 ASME B16.5 Class 300 welding neck flange, RF. The flange thickness, bolting dimensions, raised face dimensions shall be furnished as per 8″ of Class 300 welding neck flange. The diameter of hub, welding end dimensions, bore diameter, and height of the hub shall be furnished as per 3″ of Class 300 welding neck flange.
  • 8″ × 2″ Class 150 reducing threaded flange, RF. Use regular 8″ Class 150 blind flange tapped with NPS 2 taper pipe thread in accordance with ASME B1.20.1.

Maybe you like also

  • ABOUT US

    We have been dedicating ourselves to piping and pipeline engineering since the inception. The company provides integrated solution to package supply of various piping & pipeline materials, components, and equipment.

  • CONTACT US

    Room 502, No.448 Heping West Road, Shijiazhuang, Hebei Province, China
    Tel: +86-311-67906676
    Fax: +86-311-67906676
    Email:  sales@pipingpipeline.com
    Whatsapp: 0086-15076331069

  • Service
    Work Time: 8:30-18:00
    Welcome to contact us at your best convenience.